Question # 1 During a wireless network design, a customer requires wireless coverage on the perimeter of a building but also wants to minimize signal leakage from the wireless network. Which antenna should be used to accomplish this design? A. PatchB. DipoleC. MonopoleD. Omnidirectional
Click for Answer
A. Patch
Answer Description Explanation:
A Patch antenna should be used to provide wireless coverage on the perimeter of a building while minimizing signal leakage. Patch antennas have a directional radiation pattern that can be focused along the perimeter.
https://www.cisco.com/c/en/us/td/docs/routers/connectedgrid/antennas/installing-combined/industrial-routers-and-industrial-wireless-antenna-guide/ANT-MP-INT-OUT-M.html
Question # 2 An enterprise is using the wireless network as the main network connection for corporate users and guests. To wireless network availability. Two Standalone controllers are installed in the head office. APs are connected to the controllers using a round-robin approach to load balance the traffic. After a power cut, the wireless clients disconnect while roaming. An engineer tried eping from the controller but faits. Which protocol needs to be allowed between the networks that the controllers are installed? A. IP Protocol 67B. IP Protocol 77C. IP Protocol 87D. IP Protocol 97
Click for Answer
D. IP Protocol 97
Answer Description Explanation:
The protocol that needs to be allowed between the networks where the controllers are installed is IP Protocol 97, which is used for encapsulating IP within IP, often used in network mobility and IP tunneling.
Question # 3 An engineer must create data-link redundancy for the company’s Cisco Wireless LAN Controller. The engineer has decided to configure LAG-based redundancy instead of port-based redundancy. Which three features of LAG-based redundancy influenced this decision? (Choose three.) A. Packets are always sent out on the same port they are received on.B. All interface traffic passes as long as one port is up.C. The same port has multiple untagged dynamics interfaces.D. Interface connection to two separate nonstacked switches is available.E. Full bandwidth of all links is available.
Click for Answer
B. All interface traffic passes as long as one port is up.E. Full bandwidth of all links is available.
Answer Description Explanation:
LAG-based redundancy is chosen for its ability to provide continuous connectivity as long as one port in the LAG is operational (B), utilize the full bandwidth capacity of all the links in the LAG (E), and allow for the grouping of ports into multiple LAGs for increased redundancy and bandwidth (F). References: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide.
Question # 4 A 60,000-square-foot outdoor area must be surveyed. The survey must be completed in the least amount of time. Which tool or equipment is used when performing the site survey? A. additional access points that use sniffer modeB. site survey tool that has modules in sniffer modeC. Additional access points that use GPS modeD. site survey tool that has a GPS module
Click for Answer
D. site survey tool that has a GPS module
Answer Description Explanation:
When performing a site survey of a large outdoor area, a site survey tool with a GPS module is ideal. The GPS module allows for precise location tracking, which is essential for mapping signal coverage over a large area. This tool can help complete the survey efficiently by automatically recording the location of signal measurements
Question # 5 An engineer is designing a solution where guests terminate on an anchor controller in the DMZ. The engineer is having issues and wants to test connectivity between members of a mobility group. Which command must be issued to test whether a mobility control packet is able to be reached over the management interface? A. show loggingB. mappingC. mappingD. tracert
Click for Answer
D. tracert
Answer Description Explanation:
The ‘tracert’ command is used to test connectivity between members of a mobility group by tracing the path that mobility control packets take over the network. This command helps identify any potential issues with the route that the packets are taking, which could affect the ability of guests to connect to the anchor controller in the DMZ. References := (CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide Premium Edition and Practice)
Question # 6 An engineer is performing an AP-on-a-stick survey and ¬nds that the 5 GHz channel overlap is too high when an appropriate number of APs are used for the density requirements. Which two actions during the survey reduce channel overlap? (Choose two.) A. Raise the minimum data rate to 24 Mbps.B. Increase AP transmit power to improve the SNR.C. Allow the use of UNII-2e channels.D. Use directional antennas to limit the coverage area of some APs.E. Enable power saving mode.
Click for Answer
A. Raise the minimum data rate to 24 Mbps.D. Use directional antennas to limit the coverage area of some APs.
Answer Description Explanation:
Raising the minimum data rate to 24 Mbps will reduce the range at which devices can connect, thereby reducing channel overlap. Using directional antennas can also help limit the coverage area of some APs, which can further reduce channel overlap by focusing the signal in specific directions rather than in a broad coverage pattern. References: Designing Cisco Enterprise Wireless Networks (ENWLSD 300-425)
Question # 7 An engineer must perform an assessment of a customer LAN for a future IEEE 802.11ac Wave 2 wireless deployment All access switches are Fast Ethernet-Capable only, and the wired infrastructure between existing APs and access switches is based on the CAT 6A standard. Which two actions provide maximum support of Cisco 3800 Series access points? (Choose two.) A. Replace the existing switches with mGig switches.B. Replace the existing switches with gigabit switches with 10G uplinks.C. Ensure that cable distances between access switches and APs are not longer than 100 meters.D. Replace the existing wiring infrastructure with the CAT-7E wiring standard,E. Ensure that cable distances between access switches and APs are not longer than 55 meters.
Click for Answer
A. Replace the existing switches with mGig switches.B. Replace the existing switches with gigabit switches with 10G uplinks.
Answer Description Explanation:
Cisco 3800 Series APs support higher speeds provided by IEEE 802.11ac Wave 2, which Fast Ethernet switches cannot fully support. Replacing them with mGig or gigabit switches with 10G uplinks will ensure the infrastructure can handle the increased data rates. The CAT 6A standard supports these speeds, so there’s no need to replace the wiring if it’s already CAT 6A.
Question # 8 An engineer is trying to configure the APs installed in a new auditorium to use 40 MHz channels with high data rates and lower TX power. The APs in the building hallway must use lower-density design settings configured for the rest of the building. Which two configurations achieve this design? (Choose two.) A. TPCB. DCAC. RRMD. RF protocol
Click for Answer
C. RRMD. RF protocol
Answer Description Explanation:
AP groups allow the engineer to apply different policies for APs in the auditorium versus those in the hallway. RRM (Radio Resource Management) can dynamically adjust the TX power and channel settings to optimize the wireless coverage and capacity.
Up-to-Date
We always provide up-to-date 300-425 exam dumps to our clients. Keep checking website for updates and download.
Excellence
Quality and excellence of our Designing Cisco Enterprise Wireless Networks (ENWLSD) practice questions are above customers expectations. Contact live chat to know more.
Success
Your SUCCESS is assured with the 300-425 exam questions of passin1day.com. Just Buy, Prepare and PASS!
Quality
All our braindumps are verified with their correct answers. Download CCNP Enterprise Practice tests in a printable PDF format.
Basic
$80
Any 3 Exams of Your Choice
3 Exams PDF + Online Test Engine
Buy Now
Premium
$100
Any 4 Exams of Your Choice
4 Exams PDF + Online Test Engine
Buy Now
Gold
$125
Any 5 Exams of Your Choice
5 Exams PDF + Online Test Engine
Buy Now
Passin1Day has a big success story in last 12 years with a long list of satisfied customers.
We are UK based company, selling 300-425 practice test questions answers. We have a team of 34 people in Research, Writing, QA, Sales, Support and Marketing departments and helping people get success in their life.
We dont have a single unsatisfied Cisco customer in this time. Our customers are our asset and precious to us more than their money.
300-425 Dumps
We have recently updated Cisco 300-425 dumps study guide. You can use our CCNP Enterprise braindumps and pass your exam in just 24 hours. Our Designing Cisco Enterprise Wireless Networks (ENWLSD) real exam contains latest questions. We are providing Cisco 300-425 dumps with updates for 3 months. You can purchase in advance and start studying. Whenever Cisco update Designing Cisco Enterprise Wireless Networks (ENWLSD) exam, we also update our file with new questions. Passin1day is here to provide real 300-425 exam questions to people who find it difficult to pass exam
CCNP Enterprise can advance your marketability and prove to be a key to differentiating you from those who have no certification and Passin1day is there to help you pass exam with 300-425 dumps. Cisco Certifications demonstrate your competence and make your discerning employers recognize that Designing Cisco Enterprise Wireless Networks (ENWLSD) certified employees are more valuable to their organizations and customers. We have helped thousands of customers so far in achieving their goals. Our excellent comprehensive Cisco exam dumps will enable you to pass your certification CCNP Enterprise exam in just a single try. Passin1day is offering 300-425 braindumps which are accurate and of high-quality verified by the IT professionals. Candidates can instantly download CCNP Enterprise dumps and access them at any device after purchase. Online Designing Cisco Enterprise Wireless Networks (ENWLSD) practice tests are planned and designed to prepare you completely for the real Cisco exam condition. Free 300-425 dumps demos can be available on customer’s demand to check before placing an order.
What Our Customers Say
Jeff Brown
Thanks you so much passin1day.com team for all the help that you have provided me in my Cisco exam. I will use your dumps for next certification as well.
Mareena Frederick
You guys are awesome. Even 1 day is too much. I prepared my exam in just 3 hours with your 300-425 exam dumps and passed it in first attempt :)
Ralph Donald
I am the fully satisfied customer of passin1day.com. I have passed my exam using your Designing Cisco Enterprise Wireless Networks (ENWLSD) braindumps in first attempt. You guys are the secret behind my success ;)
Lilly Solomon
I was so depressed when I get failed in my Cisco exam but thanks GOD you guys exist and helped me in passing my exams. I am nothing without you.